• Internal and external floors and walls and/or walls in contact with soil moisture;
• Basements, underground works and retaining walls;
• Rigid pavements, special and current works of art, sidewalks, precast concrete in general;
• Swimming pools, reservoirs, cisterns, water tanks, tunnels and galleries, diaphragm walls;
• Concrete slabs and fiber cement tiles;
• Wood such as fences, posts, plywood and planks.

The average yield of the product is 3.45 m²/L per coat:

• 3 coats: Reservoirs, swimming pools, retaining walls, uncovered slabs and floors in contact with the ground
• 2 coats: Other locations

Polymeric mortars such as: Viaplus 5000, Viaplus 7000, Viaplus top, Sikatop flex. Asphalt and aluminized blankets such as: Torodin, Viapol, Vedamax and Dryko.

Product certified by HBC (Healthy Building Certificate) qualified and certified product, as a product that does not pose any risk to human health and the environment, therefore being a healthy and sustainable product.

SGS USA: Report of Product Testing Report – Interim Product: MOSHE 3000 FLEX Lab No.: 22-551, it was found that in the ASTM C1583 – Bond Strength to Concrete test, the product withstood a pressure of 100 Psi in the tests with 7 and 28 days of cure, in the ASTM D6904 – Wind-Driven Rain test, it was found that the product withstood water spray for approximately 24 hours where the water was sprayed at a rate of 60 to 70 gallons per hour and 5 inches of water pressure (equivalent dynamic pressure at a wind speed of 98 mph) without water passage and in the ASTM E96 – Water Vapor Transmission test, it was found that when tested at a temperature of 73.4 ± 2ºF and relative humidity of 50 +/- 2%, Water Vapor Transmission – 20 thousand WFT (perm) of 3.7 to 4.5 occurred. 28 days.

IPT TEST REPORT No. 1 131 867-203, it was found that in the tests according to the ABNT NBR 10.787 test on Water penetration under positive pressure, it was found that there was no water penetration into the test specimen, after application of a pressure of (0.10 ± 0.01) MPa for 48 hours, followed by application of a pressure of (0.25 ± 0.01) MPa for 24 hours. According to the ABNT NBR 10.787 and 11.905 tests on Water penetration under negative pressure, the product was shown to be watertight up to a pressure of at least 0.10 MPa for 48 hours. According to the ABNT NBR 12.171 test on Tensile adhesion strength (minimum), the product demonstrated an average strength of 3.8 MPa, much higher than the standard that requires at least 0.5 MPa. According to the ABNT NBR 7462 test on Elongation at break (minimum), the product reached 3% and Elongation at break after aging (minimum), the product reached 5%, higher than the expansion of concrete, which is 0.03%.

IPT TEST REPORT No. 1 140 327-203, it was found that in the tests according to ASTM D2369-20 – Standard Test Method for Volatile Content of Coatings (Procedure IPT6806 – Rev. 8), ASTM 4017-22 – Standard Test Method for Water in Paints and Paint Materials by Karl Fischer Method and United States Environmental Protection Agency (USEPA) Method 24 – Determination of Volatile Matter Content, Water Content, Density, Volume Solids, And Weight Solids of Surface Coatings – method for water-based coating, it was found that the volatile content, non-aqueous – g/L of MOSHE 3000 FLEX is 19.3 g/L, which is much lower than the limits required by the USGBC LEED Certification, which according to the South Coast Air Quality Management District (SCAQMD) Rule 1113, effecitve June 3, 2011 is 400 g/L.