MOSHE 3000 FLEX METAL was developed with nanotechnology, 100% inert minerals and water-based acrylic resins. It has tested and proven hydrophobic properties as the best technical solution on the market for the recovery and prevention of pathologies in waterproofing and oxidation of metal tiles, sheets and structures. It is a flexible product that creates surface protection, providing high waterproofing, closing fissures and cracks even with small movements and expansions and combating oxidation on metal surfaces. It can be pigmented to other colors.
It is a 3-in-1 liquid, single-component waterproofing and water-repellent product (treats oxidation, waterproofs and paints), providing great ease and speed in application, acting as a primer, primer, paint and waterproofing at the same time. It is highly durable, since it is composed of inert minerals. It comes ready to use and is easy to apply; just open the bucket and mix mechanically for 2 minutes before application. In this way, MOSHE FLEX METAL prevents infiltration, increases the durability of the construction and prevents the proliferation of fungi and bacteria, and treats oxidation of surfaces.
MOSHE 3000 FLEX METAL creates a protective film, sealing all pores, fissures and cracks in metal surfaces. It has excellent results for both positive and negative pressure of water acting on the surface, ensuring excellent waterproofing. It is also resistant to the effects of ultraviolet rays and combats rust.
5-year warranty according to performance reports proven by third-party laboratories, except for design flaws, structural flaws or misuse of the material. The product can be pigmented to other colors with inert and natural pigments in powder or liquid form, on site or using machines in home centers.
The product yields up to 3.45 m²/L/coat, depending on the roughness of the applied surface. The more porous, the lower the yield.
Metal Primers and Primers such as: Eucafer Eucatex Primer, Suvinil Zarcão, Luxcollor Zarcão, Coralit Zarcão, Super Galvite, Resvestik Liquid Rubber, hm Rubber Liquid Rubber, Lit Epoxy Paint.
Product certified by HBC (Healthy Building Certificate) qualified and certified product, as a product that does not pose any risk to human health and the environment, therefore being a healthy and sustainable product.
According to SGS USA Report: Report of Product Testing Report – Interim Product: MOSHE 3000 FLEX Lab No.: 22-551, it was found that in the ASTM C1583 test – Bond Strength to Concrete, the product withstood a pressure of 100 Psi in the tests with 7 and 28 days of curing, in the ASTM D6904 test – Wind-Driven Rain, it was found that the product withstood water spray for approximately 24 hours where the water was sprayed at a rate of 60 to 70 gallons per hour and 5 inches of water pressure (equivalent to dynamic pressure at a wind speed of 98 mph) without water passage and in the ASTM E96 test – Water Vapor Transmission, it was found that when tested at a temperature of 73.4 ± 2oF and relative humidity 50 +/- 2%, Water Vapor Transmission occurred – 20 thousand WFT (perm) of 3.7 at 28 days.
According to the IPT Report TEST REPORT No. 1 131 867-203, it was found that in the tests according to the ABNT NBR 10.787 test on Water penetration under positive pressure, it was found that there was no water penetration into the test specimen, after application of a pressure of (0.10 ± 0.01) MPa for 48 hours, followed by application of a pressure of (0.25 ± 0.01) MPa for 24 hours. According to the ABNT NBR 10.787 and 11.905 tests on Water penetration under negative pressure, the product was shown to be watertight up to a pressure of at least 0.10 MPa for 48 hours. According to the ABNT NBR 12.171 test on Tensile adhesion strength (minimum), the product demonstrated an average strength of 3.8 MPa, much higher than the standard that requires at least 0.5 MPa. According to the ABNT NBR 7462 test on Elongation at break (minimum), the product reached 3% and Elongation at break after aging (minimum), the product reached 5%, higher than the expansion of concrete, which is 0.03%.
According to IPT Report TEST REPORT No. 1 140 327-203, it was found that in the tests according to ASTM D2369-20 - Standard Test Method for Volatile Content of Coatings (Procedure IPT6806 - Rev. 8), ASTM 4017-22 - Standard Test Method for Water in Paints and Paint Materials by Karl Fischer Method and United States Environmental Protection Agency (USEPA) Method 24 - Determination of Volatile Matter Content, Water Content, Density, Volume Solids, And Weight Solids of Surface Coatings - method for water-based coating, it was found that the volatile content, non-aqueous - g/L of MOSHE 3000 FLEX is 19.3 g/L, which is much lower than the limits required by the USGBC LEED Certification, which according to the South Coast Air Quality Management District (SCAQMD) Rule. 1113, effective June 3, 2011 is 400 g/L.
Our team is ready to answer all your questions about Moshe 3000.
Get in touch
